add doc

中控红外模块使用手册.md

@@ -0,0 +1,97 @@
+# 中控红外模块使用手册
+
+## 1.串口软件部分
+
+打开串口设置软件
+
+网络学习型红外(串网设置+同步mac) -> 红外(网控+串网设置+同步mac).exe
+
+![](Img/1_0.png)
+
+打开后，选择模块设置
+
+![](Img/1_1.png)
+
+模块设置进入后，点击串口选择
+
+![](Img/1_2.png)
+
+CH340插入主机的USB端口，并且选择刚才插入的串口号，其他设置默认就好。
+
+![](Img/1_3.png)
+
+设置完之后，点击确定，如果没检测出来就装一下CH340驱动，Win10一般是免驱。
+
+如果上一步成功链接串口，下面进入设置项，按照如下图示把设置项设置好，主模块用于录制的，请按照下面固定格式填好，非录制用的，ip地址请务必与下面的地址区分开，比如192.168.1.201，192.168.1.202都是可以的。
+
+![](Img/1_4.png)
+
+如果串口写入成功了，红外模块插入网线+电源，可以通过该软件查看一下是否生效
+
+关闭模块设置窗口，点击客户端模式，填写ip地址端口号，点击链接模块，模块显示红色即为设置成功
+
+![](Img/1_5.png)
+
+## 2.中控软件录制协议
+
+#### 使用软件前，必须保证红外模块192.168.1.200该模块可正常工作！
+
+进入展厅控制
+
+![](Img/2_0.png)
+
+点击电视遥控，点击录制
+
+![](Img/2_1.png)
+
+进入该界面时，准备好遥控器，红外发射器
+
+![](Img/2_2.jpg)
+
+按下按键时，请不要点击关闭按钮，红外发射器会如下所示，此时使用遥控器对准该位置，按下上图所示关闭键，设备接收到信号会关闭红灯显示，同时，上述遥控录制界面会解除录制状态，此时该开机指令已经学习完毕。
+
+![](Img/2_3.png)
+
+重复上述操作，直至所有按键录入完毕，除非特殊需要，尽量不要在录制中途退出。等待所有按键处于弹起状态在进行录入即可
+
+注意：如果录制中途6s内，没有遥控器给模块发送指令，则会自动退出录制，UI会自动弹起，再次按下可以再次录制。
+
+## 3.中控软件遥控测试
+
+如果上面的步骤成功录制完毕，则点击右侧测试，进入测试页面，可以测试刚才模块录入的指令是否生效
+
+![](Img/2_4.png)
+
+进入测试页面后，再次按下对应按钮，则可以测试刚才录入的结果。
+
+![](Img/2_5.png)
+
+如果成功录入，按下对应按键，红外模块红灯闪烁，即为成功。
+
+最后需要让红外模块对准电视的开关，然后使用平板进行控制即可。
+
+## 4.中控软件遥控配置
+
+右上角返回到主界面，点击左上角连点4-5次，调出后台设置窗口
+
+![](Img/4_0.png)
+
+![](Img/4_1.png)
+
+![](Img/4_2.png)
+
+进入遥控设置后，可以点击创建遥控器
+
+![](Img/4_3.jpg)
+
+创建遥控器时，需要保证串口已经配置过对应的Ip地址且设备可用。
+
+![](Img/4_4.png)
+
+创建后可以按下对应的按键进行编辑或者删除
+
+![](Img/4_5.png)
+
+退出并且进入到电视遥控界面后，可以看到刚才创建的遥控器了
+
+![](Img/4_6.png)

网络学习型红外(串网设置+同步mac)/USB转串口CH340驱动/DRIVER/CH341SER.INF

@@ -0,0 +1,212 @@
+; CH341SER.INF
+; Driver for CH341 (USB=>SERIAL chip) V3.1
+; WDM&VXD for Windows 98/Me/2000/XP/Server2003/Vista/64bit XP/64bit Vista
+; Copyright (C) W.ch 2001-2009
+;
+
+[Version]
+Signature = "$Chicago$"
+Class     = Ports
+ClassGuid = {4D36E978-E325-11CE-BFC1-08002BE10318}
+Provider  = %WinChipHead%
+DriverVer = 06/03/2009, 3.1.2009.06
+
+[ControlFlags]
+ExcludeFromSelect = USB\VID_1A86&PID_7523
+ExcludeFromSelect = USB\VID_1A86&PID_5523
+ExcludeFromSelect = USB\VID_4348&PID_5523
+ExcludeFromSelect = USB\VID_4348&PID_5523&REV_0250
+ExcludeFromSelect = USBSERPORT\SER5523
+ExcludeFromSelect = CH341PORT\SER5523
+
+[Manufacturer]
+%WinChipHead% = WinChipHead
+%WinChipHead% = WinChipHead,NTamd64
+%WinChipHead% = WinChipHead,NTia64
+
+[WinChipHead]
+%CH340SER.DeviceDesc% = CH341SER_Install, USB\VID_1A86&PID_7523
+%CH341ASER.DeviceDesc% = CH341SER_Install, USB\VID_1A86&PID_5523
+%CH341SER.DeviceDesc% = CH341SER_Install, USB\VID_4348&PID_5523
+%CH340SER.DeviceDesc% = CH341SER_Install, USB\VID_4348&PID_5523&REV_0250
+%CH341S98.DeviceDesc% = CH341S98_Install, USBSERPORT\SER5523
+%CH341S98.DeviceDesc% = CH341S98_Install, CH341PORT\SER5523
+
+[WinChipHead.NTamd64]
+%CH340SER.DeviceDesc% = CH341SER_Inst.NTamd64, USB\VID_1A86&PID_7523
+%CH341ASER.DeviceDesc% = CH341SER_Inst.NTamd64, USB\VID_1A86&PID_5523
+%CH341SER.DeviceDesc% = CH341SER_Inst.NTamd64, USB\VID_4348&PID_5523
+%CH340SER.DeviceDesc% = CH341SER_Inst.NTamd64, USB\VID_4348&PID_5523&REV_0250
+%CH341S98.DeviceDesc% = CH341S98_Inst.NTamd64, USBSERPORT\SER5523
+%CH341S98.DeviceDesc% = CH341S98_Inst.NTamd64, CH341PORT\SER5523
+
+[WinChipHead.NTia64]
+%CH340SER.DeviceDesc% = CH341SER_Inst.NTia64, USB\VID_1A86&PID_7523
+%CH341ASER.DeviceDesc% = CH341SER_Inst.NTia64, USB\VID_1A86&PID_5523
+%CH341SER.DeviceDesc% = CH341SER_Inst.NTia64, USB\VID_4348&PID_5523
+%CH340SER.DeviceDesc% = CH341SER_Inst.NTia64, USB\VID_4348&PID_5523&REV_0250
+%CH341S98.DeviceDesc% = CH341S98_Inst.NTia64, USBSERPORT\SER5523
+%CH341S98.DeviceDesc% = CH341S98_Inst.NTia64, CH341PORT\SER5523
+
+[CH341SER_Install]
+DelFiles  = CH341S98.DelFiles.SYS
+CopyFiles = CH341SER.CopyFiles.SYS, CH341SER.CopyFiles.DLL
+AddReg    = CH341SER.9X.AddReg, CH341SER.AddReg
+
+[CH341SER_Install.NT]
+CopyFiles = CH341SER.NT.CopyFiles.SYS, CH341SER.CopyFiles.DLL
+AddReg    = CH341SER.NT.AddReg, CH341SER.AddReg
+
+[CH341SER_Install.NT.HW]
+AddReg    = CH341SER.NT.HW.AddReg
+
+[CH341SER_Inst.NTamd64]
+CopyFiles = CH341SER.NT.CopyFiles.SYSA64
+AddReg    = CH341SER.NT.AddReg, CH341SER.AddReg
+
+[CH341SER_Inst.NTamd64.HW]
+AddReg    = CH341SER.NT.HW.AddReg
+
+[CH341SER_Inst.NTia64]
+CopyFiles = CH341SER.NT.CopyFiles.SYSI64
+AddReg    = CH341SER.NT.AddReg, CH341SER.AddReg
+
+[CH341SER_Inst.NTia64.HW]
+AddReg    = CH341SER.NT.HW.AddReg
+
+[CH341S98_Install]
+DelFiles  = CH341S98.DelFiles.SYS
+CopyFiles = CH341S98.CopyFiles.VXD, CH341SER.CopyFiles.SYS
+AddReg    = CH341S98.9X.AddReg, CH341S98.AddReg
+
+[CH341S98_Install.NT]
+
+[CH341S98.DelFiles.SYS]
+CH341S98.SYS, , , 1
+
+[CH341SER.CopyFiles.SYS]
+CH341S98.SYS, , , 2
+
+[CH341SER.NT.CopyFiles.SYS]
+CH341SER.SYS, , , 2
+
+[CH341SER.NT.CopyFiles.SYSA64]
+CH341S64.SYS, , , 2
+
+[CH341SER.NT.CopyFiles.SYSI64]
+;CH341I64.SYS, , , 2
+
+[CH341S98.CopyFiles.VXD]
+CH341SER.VXD, , , 2
+
+[CH341SER.CopyFiles.DLL]
+CH341PT.DLL, , , 2
+;安装DLL是可选的,DLL可以用于识别CH341端口和监视CH341端口的插拔事件
+
+[CH341SER.9X.AddReg]
+HKR, , DevLoader, , *NTKERN
+HKR, , NTMPDriver, , CH341S98.SYS
+
+[CH341SER.NT.AddReg]
+HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
+
+[CH341SER.NT.HW.AddReg]
+HKR,,"UpperFilters",0x00010000,"serenum"
+;上面这行用于枚举接在串口的即插即用设备,启动时将产生DTR和RTS信号,如果需要枚举,请将上面这行的分号去掉
+
+[CH341S98.9X.AddReg]
+HKR, , DevLoader, , *vcomm
+HKR, , PortDriver, , CH341SER.VXD
+HKR, , Contention, , *vcd
+HKR, , ConfigDialog, , serialui.dll
+HKR, , DCB, 3, 1C,00,00,00, 80,25,00,00, 11,00,00,00, 00,00,0A,00, 0A,00,08,00, 00,11,13,00, 00,00,00,00
+HKR, , PortSubClass, 1, 01
+HKR, , EnumPropPages, , "serialui.dll,EnumPropPages"
+HKR, , Enumerator, , serenum.vxd
+;上面这行用于枚举接在串口的即插即用设备,启动时将产生DTR和RTS信号,如果需要枚举,请将上面这行的分号去掉
+
+[CH341SER.AddReg]
+HKLM, SOFTWARE\WinChipHead\IC\CH341SER, WDM, 0x00010001, 0x00000031
+HKLM, SOFTWARE\WinChipHead\IC\CH341PORT, DLL, 0x00010001, 0x00000010
+HKLM, SOFTWARE\WinChipHead\IC\CH341SER, Function, , "USB=>Serial"
+;HKLM, SYSTEM\CurrentControlSet\Services\CH341SER, UserRemoval, 0x00010001, 0x00000001
+;上面这行用于在系统托盘中显示“安全删除USB转SERIAL硬件设备”，便于用户手工删除硬件
+
+[CH341S98.AddReg]
+HKLM, SOFTWARE\WinChipHead\IC\CH341SER, VXD, 0x00010001, 0x00000023
+
+[CH341SER_Install.NT.Services]
+AddService = CH341SER, 2, CH341SER.Service
+AddService = Serenum, , Serenum_Service_Inst
+
+[CH341SER_Inst.NTamd64.Services]
+AddService = CH341SER, 2, CH341SER.ServiceA64
+AddService = Serenum, , Serenum_Service_Inst
+
+[CH341SER_Inst.NTia64.Services]
+AddService = CH341SER, 2, CH341SER.ServiceI64
+AddService = Serenum, , Serenum_Service_Inst
+
+[CH341SER.Service]
+DisplayName   = "CH341SER"
+ServiceType   = 1
+StartType     = 3
+ErrorControl  = 1
+ServiceBinary = %10%\System32\Drivers\CH341SER.SYS
+
+[CH341SER.ServiceA64]
+DisplayName   = "CH341SER"
+ServiceType   = 1
+StartType     = 3
+ErrorControl  = 1
+ServiceBinary = %10%\System32\Drivers\CH341S64.SYS
+
+[CH341SER.ServiceI64]
+DisplayName   = "CH341SER"
+ServiceType   = 1
+StartType     = 3
+ErrorControl  = 1
+ServiceBinary = %10%\System32\Drivers\CH341I64.SYS
+
+[Serenum_Service_Inst]
+DisplayName    = "SerEnum"
+ServiceType    = 1
+StartType      = 3
+ErrorControl   = 1
+ServiceBinary  = %12%\serenum.sys
+LoadOrderGroup = PNP Filter
+
+[DestinationDirs]
+DefaultDestDir      = 10, System32\Drivers
+CH341S98.DelFiles.SYS = 11
+CH341SER.CopyFiles.SYS = 10, System32\Drivers
+CH341SER.NT.CopyFiles.SYS = 10, System32\Drivers
+CH341S98.CopyFiles.VXD = 11
+CH341SER.CopyFiles.DLL = 11
+CH341SER.NT.CopyFiles.SYSA64 = 10, System32\Drivers
+CH341SER.NT.CopyFiles.SYSI64 = 10, System32\Drivers
+
+[SourceDisksFiles]
+CH341SER.SYS  = 1
+CH341S98.SYS  = 1
+CH341SER.VXD  = 1
+CH341PT.DLL   = 1
+CH341I64.SYS  = 1
+CH341S64.SYS  = 1
+
+
+[SourceDisksNames]
+1 = "CH341 Serial Installation Disk", CH341SER.INF, ,
+
+[SourceDisksNames.amd64]
+1 = "CH341 Serial Installation Disk", CH341SER.INF, ,
+
+[SourceDisksNames.ia64]
+1 = "CH341 Serial Installation Disk", CH341SER.INF, ,
+
+[Strings]
+WinChipHead      = "wch.cn"
+CH341SER.DeviceDesc = "USB-SERIAL CH341"
+CH341S98.DeviceDesc = "USB-SERIAL CH341"
+CH340SER.DeviceDesc = "USB-SERIAL CH340"
+CH341ASER.DeviceDesc = "USB-SERIAL CH341A"

网络学习型红外(串网设置+同步mac)/红外模块设置.ini

@@ -0,0 +1,29 @@
+[Ä£¿éÉèÖÃ]
+In1=192
+In2=168
+In3=1
+In4=200
+In5=192
+In6=168
+In7=1
+In8=1
+In9=255
+In10=255
+In11=255
+In12=0
+In13=5000
+In14=192
+In15=168
+In16=1
+In17=55
+In18=6000
+In19=100
+In20=101
+In21=102
+In22=103
+In23=1
+In24=200
+[»ù±¾²ÎÊý]
+´®¿ÚºÅ=4
+¹¤×÷ģʽ=0
+³¬Ê±ÖØÆô=1